? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com f3046_c4ae_radial ? 1/5/2016 1 benefts ? self-healing ? low losses ? high ripple current ? high capacitance density ? high contact reliability ? suitable for high frequency applications overview the c4ae series is a polypropylene metallized flm with rectangular plastic box type flled with resin and 2 or 4 tinned copper wires. applications typical applications include dc fltering and energy storage. printed circuit board mount power film capacitors c4ae series, radial, 2 or 4 leads, 450 C 1,100 vdc, for dc link part number system c4 ae g b u 4450 a1 w j series type rated voltage (vdc) case number of leads capacitance code (pf) lead diameter (mm) size code tolerance c4 = mkp capacitors ae = radial box, dc-link application g = 450 h = 600 j = 700 o = 900 q = 1,100 b = plastic box with epoxy resin sealing u = 2 lead w = 4 lead digits 2 C 4 indicate the frst three digits of the capacitance value. first digit indicates the number of zeros to be added. a1 = 0.8 a3 = 1.2 see dimension table j = 5% one world. one kemet
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com f3046_c4ae_radial ? 1/5/2016 2 dimensions C millimeters size code p s b h 0.4 0.4 maximum maximum maximum +0/-2 w 27.5 11 20 31.5 6 x 27.5 13 25 31.5 6 y 27.5 14 28 31.5 6 1 27.5 19 29 31.5 6 2 27.5 22 37 31.5 6 f 37.5 10.2 20 40 41.5 6 h 37.5 10.2 24 44 41.5 6 j 37.5 10.2 28 37 42.5 6 l 37.5 20.3 30 45 42 6 m 52.5 20.3 30 45 57.5 6 n 52.5 20.3 35 50 57.5 6 qualifcation reference standards iec 61071 climatic category 40/85/56 according to iec 60068-1 power and ac film capacitors printed circuit board mount power film capacitors C c4ae series, radial, 2 or 4 leads, 450 C 1,100 vdc, for dc link 0.5 p p 4pin 2pin p 1 p1 l h ll d b p 0.5 b
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com f3046_c4ae_radial ? 1/5/2016 3 general technical data dielectric polypropylene metallized flm - non inductive self-healing application dc fltering / dc-link maximum operating temperature +105c upper temperature t max +85c iec 61071, endurance test temperature lower temperature t min -40c protection "solvent resistant plastic case ul94 v-0 thermosetting resin sealing ul94 v-0 compliant" installation any position leads tinned copper wires packaging packed in cardboard trays with protection for the terminals rohs compliant compliant with the restricted substance requirements of directive 2002/95/ec electrical characteristics capacitance tolerance 5% at +25c dissipation factor (df) 0.0002 at 10 khz and +25c (5c) surge voltage 1.5 * v ndc for maximum 10 times in life time at 25c overvoltage (iec 61071) 1.15 * v ndc for maximum 30 minutes - once per day 1.3 * v ndc for maximum 1 minute - once per day peak non repetitive current 1.5 * i pkr - maximum 1000 times in life time insulation resistance ir x c 30.000 seconds at 100 vdc 1 minute (+25c) capacitance deviation in operation 1.5% maximum on capacitance value measured at (+25c) permissible relative humidity annual average 70%; 85% on 30 days/year randomly distributed throughout the year. dewing not admissible life expectancy life expectancy 100.000 hours at v ndc @ hot-spot temperature t hs = +85c capacitance drop at end of life -5% (typical) failure rate iec 61709 300 fit at v ndc @ hot-spot temperature t hs = +85c test method test voltage between terminals 1.5 * v ndc for 10 seconds or 1.65 v ndc for 2 seconds, at +25c test voltage between terminals and case 3.2 kvac 50 hz for 2 seconds damp heat iec 60068-2-78 change of temperature iec 60068-2-14 power and ac film capacitors printed circuit board mount power film capacitors C c4ae series, radial, 2 or 4 leads, 450 C 1,100 vdc, for dc link
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com f3046_c4ae_radial ? 1/5/2016 4 0 . 8 0 0 . 9 0 1 . 0 0 1 . 1 0 1 . 2 0 1 . 3 0 1 . 4 0 1 . 5 0 1 0 1 0 0 1 , 0 0 0 1 0 , 0 0 0 1 0 0 , 0 0 0 1 , 0 0 0 , 0 0 0 <5 5 7 0 8 5 1 0 0 1 0 5 h ot s pot te mpe r a t ur e [ o c ] li fe ti m e ex pe c ta nc y [h] vol ta ge r a ti o [v/ v n d c ] lifetime curve v ndc = 600 v- and v ndc = 700 v- 0 . 8 0 0 . 9 0 1 . 0 0 1 . 1 0 1 . 2 0 1 . 3 0 1 . 4 0 1 . 5 0 1 0 1 0 0 1 , 0 0 0 1 0 , 0 0 0 1 0 0 , 0 0 0 1 , 0 0 0 , 0 0 0 <5 5 7 0 8 5 1 0 0 1 0 5 li fe ti m e ex pe c ta nc y [h] vol ta ge r a ti o [v/ v n d c ] h ot s pot te mpe r a t ur e [ o c ] 0 . 8 0 0 . 9 0 1 . 0 0 1 . 1 0 1 . 2 0 1 . 3 0 1 . 4 0 1 . 5 0 1 0 1 0 0 1 , 0 0 0 1 0 , 0 0 0 1 0 0 , 0 0 0 1 , 0 0 0 , 0 0 0 <5 5 7 0 8 5 1 0 0 1 0 5 h ot s pot te mpe r a t ur e [ o c ] li fe ti m e ex pe c ta nc y [h] vol ta ge r a ti o [v/ v n d c ] 1 1 0 1 0 0 1 , 0 0 0 1 0 , 0 0 0 1 0 0 , 0 0 0 1 , 0 0 0 , 0 0 0 0 . 5 0 . 6 0 . 7 0 . 8 0 . 9 1 1 . 1 1 . 2 1 . 3 1 . 4 fi t v/ v n d c 1 0 5 1 0 0 8 5 7 0 <5 5 h ot s pot te mpe r a t ur e [ o c ] lifetime expectancy/failure quota graphs fit @ hot spot temperatures lifetime curve v ndc = 900 v- and v ndc = 1,100 v- lifetime curve v ndc = 450 v- notes: t hs = t amb + t t = esr * i rms 2 * rth i rms should be limited to values granting t 30c power and ac film capacitors printed circuit board mount power film capacitors C c4ae series, radial, 2 or 4 leads, 450 C 1,100 vdc, for dc link
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com f3046_c4ae_radial ? 1/5/2016 5 environmental compliance as an environmentally conscious company, kemet is working continuously with improvements concerning the environmental effects of both our capacitors and the production of them. in europe (rohs directive) and in some other geographical areas like china, legislation has been put in place to prevent the use of some hazardous materials, like lead (pb), in electronic equipment. all products in this catalog are produced to help our customers' obligations to guarantee their products to fulfll these legislative requirements. the only material of concern in our products has been lead (pb), which has been removed from all designs to fulfll the requirement of containing less than 0.1% of lead in any homogeneous material. kemet will closely follow any changes in legislation world wide and makes any necessary changes in its products, whenever needed. some customer segments like medical, military and automotive electronics may still require the use of lead in electrode coatings. to clarify the situation and distinguish products from each other, a special symbol is used on the packaging labels for rohs compatible capacitors. because of customer requirements there may appear additional markings like lf = lead free or lfw = lead free wires on the label. materials & environment the selection of materials used by kemet for the production of capacitors is the result of extensive experience and constant attention to environmental protection. kemet selects its suppliers according to iso 9001 standards and carries out statistical analysis on the materials purchased before acceptance. all materials are, to the company's present knowledge, non-toxic and free from cadmium, mercury, chrome and compounds, pcb (polychlorine triphenyl), bromide and chlorine dioxins bromurate clorurate, cfc and hcfc and asbestos. green products all kemet power flm products are rohs compliant. insulation resistance when the capacitor temperature increases, the insulation resistance decreases. this is due to increased electron activity. low insulation resistance can also be the result of moisture trapped in the windings, caused by a prolonged exposure to excessive humidity. power and ac film capacitors printed circuit board mount power film capacitors C c4ae series, radial, 2 or 4 leads, 450 C 1,100 vdc, for dc link
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com f3046_c4ae_radial ? 1/5/2016 6 dissipation factor dissipation factor is a complex function involved with the ineffciency of the capacitor . the tg may change up and down with increased temperature. for more information, please refer to performance characteristics. sealing hermetically sealed capacitors when the temperature increases, the pressure inside the capacitor increases. if the internal pressure is high enough, it can cause a breach in the capacitor which can result in leakage, impregnation, flling fuid or moisture susceptibility . resin encased/wrap & fill capacitors the resin seals on resin encased and wrap and fll capacitors will withstand short-term exposure to high humidity environments without degradation. resins and plastic tapes will form a pseudo-impervious barrier to humidity and chemicals. these case materials are somewhat porous and through osmosis can cause contaminants to enter the capacitor. the second area of contaminated absorption is the lead-wire/resin interface. since resins cannot bond 100% to tinned wires, there can be a path formed up to the lead wire into the capacitor section. aqueous cleaning of circuit boards can aggravate this condition. barometric pressure the altitude at which hermetically sealed capacitors are operated controls the voltage rating of the capacitor. as the barometric pressure decreases, the susceptibility to terminal arc-over increases. non-hermetic capacitors can be affected by internal stresses due to pressure changes. this can be in the form of capacitance changes or dielectric arc-over as well as low insulation resistance. heat transfer can also be affected by altitude operation. heat generated in operation cannot be dissipated properly and can result in high ri2 losses and eventual failure. radiation radiation capabilities of capacitors must be taken into consideration. electrical degradation in the form of dielectric embitterment can take place causing shorts or opens. power and ac film capacitors printed circuit board mount power film capacitors C c4ae series, radial, 2 or 4 leads, 450 C 1,100 vdc, for dc link
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com f3046_c4ae_radial ? 1/5/2016 7 table 1 C ratings & part number reference cap value (f) vdc dimensions (mm) dv/dt (v/s) ipkr esl esr irms* rth part number 70c@10 khz 70c@10 khz (hs/amb) b h l p p1 apk nh m arms (c/w) 4.5 450 11 20 31.5 27.5 \ 14 65 25 14.2 4.5 44 c4aegbu4450a1wj 6.8 450 13 25 31.5 27.5 \ 15 101 25 10.0 6.0 36 c4aegbu4680a1xj 10 450 14 28 31.5 27.5 \ 14 145 26 7.4 7.5 33 c4aegbu5100a1yj 12.5 450 19 29 31.5 27.5 \ 15 187 26 6.2 8.5 29 c4aegbu5125a11j 20 450 22 37 31.5 27.5 \ 15 303 28 4.8 11.0 23 c4aegbu5200a12j 30 450 20 40 41.5 37.5 10.2 10 298 30 4.1 13.0 20 c4aegbw5300a3fj 35 450 28 37 42.5 37.5 10.2 10 355 30 3.5 14.0 18 c4aegbw5350a3jj 40 450 24 44 41.5 37.5 10.2 10 406 30 3.1 16.0 17 c4aegbw5400a3hj 50 450 30 45 42 37.5 20.3 10 508 30 2.5 18.0 15 C4AEGBW5500A3LJ 75 450 30 45 57.5 52.5 20.3 7 503 35 3.4 18.0 12 c4aegbw5750a3mj 100 450 35 50 57.5 52.5 20.3 7 677 35 2.6 22.0 10 c4aegbw6100a3nj 3.3 600 11 20 31.5 27.5 \ 17 55 25 17.0 4.0 44 c4aehbu4330a1wj 5.6 600 13 25 31.5 27.5 \ 17 94 25 10.7 6.0 36 c4aehbu4560a1xj 7 600 14 28 31.5 27.5 \ 17 118 26 9.0 7.0 33 c4aehbu4700a1yj 10 600 19 29 31.5 27.5 \ 17 169 26 6.8 8.5 29 c4aehbu5100a11j 15 600 22 37 31.5 27.5 \ 17 253 28 5.3 10.5 23 c4aehbu5150a12j 20 600 20 40 41.5 37.5 10.2 11 229 30 5.3 11.0 20 c4aehbw5200a3fj 30 600 28 37 42.5 37.5 10.2 11 337 30 3.6 14.0 18 c4aehbw5300a3jj 40 600 30 45 42 37.5 20.3 11 458 30 2.8 18.0 15 c4aehbw5400a3lj 55 600 30 45 57.5 52.5 20.3 8 425 35 4.1 16.5 12 c4aehbw5550a3mj 75 600 35 50 57.5 52.5 20.3 8 579 35 3.1 20.5 10 c4aehbw5750a3nj 2.7 700 11 20 31.5 27.5 \ 19 51 25 18.3 4.0 44 c4aejbu4270a1wj 4 700 13 25 31.5 27.5 \ 19 77 25 12.9 5.5 36 c4aejbu4400a1xj 5 700 14 28 31.5 27.5 \ 19 96 26 10.7 6.0 33 c4aejbu4500a1yj 8 700 19 29 31.5 27.5 \ 19 154 26 7.3 8.0 29 c4aejbu4800a11j 12.5 700 22 37 31.5 27.5 \ 19 241 28 5.5 10.0 23 c4aejbu5125a12j 15 700 20 40 41.5 37.5 5.1 13 196 30 6.2 10.0 20 c4aejbw5150a3fj 20 700 28 37 42.5 37.5 10.2 13 262 30 4.7 12.5 18 c4aejbw5200a3jj 22 700 24 44 41.5 37.5 10.2 13 288 30 4.3 13.0 17 c4aejbw5220a3hj 30 700 30 45 42 37.5 20.3 13 389 30 3.2 16.5 15 c4aejbw5300a3lj 45 700 30 45 57.5 52.5 20.3 9 389 35 4.4 16.0 12 c4aejbw5450a3mj 55 700 35 50 57.5 52.5 20.3 9 485 35 3.6 19.0 10 c4aejbw5550a3nj 60 700 35 50 57.5 52.5 20.3 9 530 35 3.4 19.5 10 c4aejbw5600a3nj 1.5 900 11 20 31.5 27.5 \ 24 36 25 26.3 3.5 44 c4aeobu4150a1wj 2.7 900 13 25 31.5 27.5 \ 24 65 25 15.3 5.0 36 c4aeobu4270a1xj 3.3 900 14 28 31.5 27.5 \ 24 79 26 12.9 5.5 33 c4aeobu4330a1yj 5 900 19 29 31.5 27.5 \ 24 120 26 9.1 7.0 29 c4aeobu4500a11j 8 900 22 37 31.5 27.5 \ 24 193 28 6.6 9.5 23 c4aeobu4800a12j 12 900 20 40 41.5 37.5 10.2 16 190 30 6.3 10.0 20 c4aeobw5120a3fj 14 900 28 37 42.5 37.5 10.2 16 229 30 5.4 11.5 18 c4aeobw5140a3jj 16 900 24 44 41.5 37.5 10.2 16 256 30 4.8 13.0 17 c4aeobw5160a3hj 20 900 30 45 42 37.5 20.3 16 321 30 3.9 15.0 15 c4aeobw5200a3lj 30 900 30 45 57.5 52.5 20.3 11 324 35 5.2 15.0 12 c4aeobw5300a3mj 40 900 35 50 57.5 52.5 20.3 11 428 35 4.0 18.0 10 c4aeobw5400a3nj 1 1100 11 20 31.5 27.5 \ 28 28 25 33.1 3.0 44 c4aeqbu4100a1wj 1.8 1100 13 25 31.5 27.5 \ 29 52 25 19.1 4.5 36 c4aeqbu4180a1xj 2.2 1100 14 28 31.5 27.5 \ 29 63 26 16.0 5.0 33 c4aeqbu4220a1yj 3.3 1100 19 29 31.5 27.5 \ 29 95 26 11.2 6.5 29 c4aeqbu4330a11j 5 1100 22 37 31.5 27.5 \ 29 145 28 8.2 8.5 23 c4aeqbu4500a12j 8 1100 20 40 41.5 37.5 10.2 20 157 30 7.9 9.0 20 c4aeqbw4800a3fj 10 1100 28 37 42.5 37.5 10.2 20 196 30 6.3 11.0 18 c4aeqbw5100a3jj 12 1100 30 45 42 37.5 20.3 20 235 30 5.3 13.0 15 c4aeqbw5120a3lj 20 1100 30 45 57.5 52.5 20.3 13 262 35 6.5 13.0 12 c4aeqbw5200a3mj 25 1100 35 50 57.5 52.5 20.3 13 331 35 5.2 16.0 10 c4aeqbw5250a3nj 27 1100 35 50 57.5 52.5 20.3 13 354 35 4.9 16.5 10 c4aeqbw5270a3nj cap value (f) vdc b h l p p1 dv/dt (v/s) ipkr esl esr irms rth part number (1) current values that lead to a t of ~ 15c in the hot spot t hs = t amb + t = 70c + 15c = 85c for packaging quantities not listed contact kemet power and ac film capacitors printed circuit board mount power film capacitors C c4ae series, radial, 2 or 4 leads, 450 C 1,100 vdc, for dc link
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com f3046_c4ae_radial ? 1/5/2016 8 kemet corporation world headquarters 2835 kemet way simpsonville, sc 29681 mailing address: p.o. box 5928 greenville, sc 29606 www.kemet.com tel: 864-963-6300 fax: 864-963-6521 corporate off ces fort lauderdale, fl tel: 954-766-2800 north america northeast wilmington, ma tel: 978-658-1663 southeast lake mary, fl tel: 407-855-8886 central novi, mi tel: 248-994-1030 irving, tx tel: 972-915-6041 west milpitas, ca tel: 408-433-9950 mexico guadalajara, jalisco tel: 52-33-3123-2141 europe southern europe sasso marconi, italy tel: 39-051-939111 skopje, macedonia tel: 389-2-55-14-623 central europe landsberg, germany tel: 49-8191-3350800 kamen, germany tel: 49-2307-438110 northern europe wyboston, united kingdom tel: 44-1480-273082 espoo, finland tel: 358-9-5406-5000 asia northeast asia hong kong tel: 852-2305-1168 shenzhen, china tel: 86-755-2518-1306 beijing, china tel: 86-10-5877-1075 shanghai, china tel: 86-21-6447-0707 seoul, south korea tel: 82-2-6294-0550 taipei, taiwan tel: 886-2-27528585 southeast asia singapore tel: 65-6701-8033 penang, malaysia tel: 60-4-6430200 bangalore, india tel: 91-806-53-76817 note: kemet reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. kemet does not assume any responsibility for infringement that might result from the use of kemet capacitors in potential circuit designs. kemet is a registered trademark of kemet electronics corporation. power and ac film capacitors printed circuit board mount power film capacitors C c4ae series, radial, 2 or 4 leads, 450 C 1,100 vdc, for dc link
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com f3046_c4ae_radial ? 1/5/2016 9 disclaimer all product specif cations, statements, information and data (collectively, the information) in this datasheet are subject to change. the customer is responsible for checking and verifying the extent to which the information contained in this publication is applicable to an order at the time the order is placed. all information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. statements of suitability for certain applications are based on kemet electronics corporations (kemet) knowledge of typical operating conditions for such applications, but are not intended to constitute C and kemet specif cally disclaims C any warranty concerning suitability for a specif c customer application or use. the information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. any technical advice inferred from this information or otherwise provided by kemet with reference to the use of kemets products is given gratis, and kemet assumes no obligation or liability for the advice given or results obtained. although kemet designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. although all productCrelated warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. power and ac film capacitors printed circuit board mount power film capacitors C c4ae series, radial, 2 or 4 leads, 450 C 1,100 vdc, for dc link
|
